ATN PS 23 User Manual

PS-23  
nIght vISIon gogglES  
u s e r ` s g u i d e  
Important Export Restrictions! Commodities, prod-  
ucts, technologies and services contained in this manual  
are subject to one or more of the export control laws and  
regulations of the U.S. Government and they fall under the  
control jurisdiction of either the US Department of State  
or the US BIS-Department of Commerce. It is unlawful  
and strictly prohibited to export, or attempt to export or  
otherwise transfer or sell any hardware or technical data  
or furnish any service to any foreign person, whether  
abroad or in the United States, for which a license or writ-  
ten approval of the U.S. Government is required, without  
first obtaining the required license or written approval  
from the Department of the U.S. Government having  
jurisdiction. Diversion contrary to U.S. law is prohibited.  
fEatuRES  
• High Quality light intensifier tube  
protection , unit will turn off automatically if  
exposed to excessive light for more than 10  
seconds. If the unit is move away from the  
bright light, it will reactivate automatically.  
• Super fast lens system provides the user  
with a clear and sharp image  
• Built-in Infra Red illuminator lets you see  
even in total darkness  
• Rugged and versatile design  
• Single switch knob operation  
• Camera/camcorder-adaptable  
• Uses one 3V lithium battery  
• Environmental: Water resistantr  
• Lifetime warranty  
• 3x lenses (optional)  
• Adjustable Flip-up headmount for hands  
free use  
• IR-on and Low Battery indicators  
• Automatic brightness control for high-light  
aPPlIcatIon  
The PS-23 Night Vision goggles is one of the most versatile night vision devices available. This unit  
can be handheld, head-mounted for hands free usage, it is camera/ camcorder adaptable, and can  
be 3x binocular. The intergrated IR illuminator enhances the ability of the user to read maps and oper-  
ate in confined, zero light areas. The PS-23 is available with several image intensifier options to meet  
a wide array of specification requirements.  
The PS-23 night vision goggles is a complex opticoelectronic system for individual use. The device  
consists of the objective lens assembly, eyepiece and the body. The body contains an image inten-  
sifier tubes assembly with an integrated high voltage power source and the battery housing.  
Objective lens protective cover is intended to protect the objective lens from dust and scratches. It  
also will act as a daylight filter, allowing you to test the scope in daylight or other bright light situa-  
tions. The pinhole in the center of the protective cover allows the user to check the operation ability  
of the device in daylight conditions.  
NOTE: Do not test the scope in daylight conditions even with the daylight filter/lens cap on for more  
than ten (10) minutes.  
oPERatIon  
• Take the goggles out of the case.  
• Install the battery(3 Volt, CR123A) into the housing with the polarity order as shown on the scope.  
• Rotate the operation knob from “OFF” position to “ON” position to turn the unit on. The protec-  
tive lens cover still attached to the lens. Do not turn the unit on in the daytime without the  
protective lens cap on. You should see green glow in the eyepiece.  
• Observe the scene and adjust the diopter for optimal image clarity.  
• You may now enter a dark environment or simply shut the lights off in order to darken the room.  
• Next, remove the lens cap/daylight filter. Adjust the front lens for the distance of the focus. You  
should not have to readjust the diopter.  
• To turn the unit off, rotate the operation knob from “ON” position to “OFF” position.  
focuSIng  
To focus the PS-23, first you will  
Operation  
need to adjust the diopter. Simply  
knob  
turn the diopter clockwise until  
it stops. Then, while looking  
through the diopter at an object,  
slowly turn the diopter back coun-  
ter clockwise until the grain in the  
image is sharp.  
2
NOTE: We suggest that you focus the diopter during daylight with the filter on.  
Next focus the front lens until the image and the grain are both sharp. When you are in low-light con-  
ditions and the daylight filter is off, you may focus the front lens to receive sharp image, the diopter  
should not be adjusted.  
NOTE: The front lens should be readjusted as you view objects at different distances.  
InfRa-RED IllumInatoR  
Infra-red illuminators, or IR illuminators, are common to night vision.  
The IR light greatly enhances the performance of the PS-23 while  
remaining almost totally invisible to the naked eye.  
Built-in Infra-red  
Illuminator  
To turn the IR on, draw and rotate the operation knob to “IR” posi-  
tion.  
It is important to remember that the IR illuminator is simply an infra  
red light source, and like any light source, it may loose its effective-  
ness over a great distance.  
flIP-uP hEaDSEt  
fIttIng thE hEaDgEaR  
1) Fit the head gear to your head size. Adjust the head  
gear fist before attaching the PS-23 to it.  
2) Loosen all the straps and place the head gear onyour  
head.  
3) Tighten the straps until the head gear fits firmly.  
googlES InStallatIon anD aJuStmEnt  
Now you are ready to mount the PS-23 on to your  
headgear.  
1) Remove the already adjusted head gear from your  
head.  
1
3
2) Push button [1] and insert the bracket [2] of the PS-23  
to the rail of the headset.  
3) Place the head gear with PS-23 onto your head.  
2
4) Loosen the screw [3] and move the unit along the rail  
for eye relief adjustment .  
The PS-23 headset has a flip-up mechanism. Push the  
button [4] on the side of mount and lift the unit up until the  
unit fixates in the top position.  
4
Push same button to lower PS-23 to viewing position.  
PRotEctIvE SyStEm  
The automatic highlight protective system analyzes light exposure with the sensor . If the level of  
light exposure exceeds allowable the red indicator will turn on. If high light exposure is kept more  
than 10 seconds the device automatically will off. If you move the unit away from the bright light  
after it shuts off the unit will turn back on. If short-term actuation of a sight in a highlight condition(for  
check of serviceability)is necessary the sensor should be closed by a cover.  
NOTE: The automatic highlight protective system and automatic brightness control system do not  
protect a sight from damage by bright light sources (a fire, headlights of the automobile, lanterns,  
etc.). Do not point the device at a bright light source.  
3
automatIc Shut-off SyStEm  
The automatic shut-off system turn the power off when the device is upright on the flip-up headset.  
When device is returned into the working position the system turn the power on again.  
450 mw InfRa-RED IllumInatoR  
(oPtIonal)  
The 450 mW IR Illuminator works on a separate  
IR Brightness Adjustment  
Battery  
battery from the main unit. To install the battery  
unscrew cap and insert battery in the same direc-  
tion as depicted by the diagram on the IR. To in-  
stall the 450mW IR Illuminator to the scope screw  
the adapter into the thread on the scope. Install IR  
to the rail of adapter and screw fixator.  
Housing  
IR Elevation  
Adapter  
The IR illuminator control buttons are located on  
its side. To switch the Digital IR illuminator on/off  
press “+” and “-” buttons simultaneously. When  
the IR illuminator is switched on you can see the  
green LED lit. By pushing the buttons “+” and “-”  
you may adjust the IR brightness.  
Fixation  
Screw  
IR Focusing  
IR Windage  
The IR beam is focusable to change the field of  
coverage. To change the beam width slightly turn the IR lens.  
You could change the IR control panel fitting your needs. The screw-tool included into the set should  
be used for weakening the fixing screw located on the IR. Rotate the IR placing it in the most conven-  
ient position. Tighten the screw with the screw-tool to fix the new position.  
For installation IR450 use adapter with Picatinny rail. Mount the adapt  
3X lEnSES  
(oPtIonal)  
The additional 3X Afocal Lenses a for PS-23 transform it to 3X binocular.  
To install 3X Afocal Lenses screw it on the front lens of PS-23.  
camERa aDaPtER  
(oPtIonal)  
To use your PS-23 with a 35mm camera or camcorder you will need the following:  
1) If you plan to use a camcorder then your camcorder must have a MACRO feature. Most modern  
camcorders today have a MACRO feature built-in.  
2) If you plan to use a 35mm camera, you will need a MACRO lens. If you don’t have one, we advise  
that you contact your local camera store.  
3) You may or may not need a STEP-UP or STEP-DOWN ring in order to adapt the camera adapter  
to your lens.  
NOTE: The camera adapter comes with 37mm and 52mm threads. If you  
need other sizes your local camera store should be able to help.  
• Remove the rubber eyecup from the PS-23  
• Screw the camera adapter onto the front of the lens on your Video camera’s  
lens or your 35mm camera’s lens.  
• Loosen the three set screws on the camera adapter.  
• Place the camera adapter over the PS-23’s eyepiece.  
• Tighten the three set screws to fit snugly to the PS-23’s eyepiece  
4
• You may need to focus the 35mm camera or video camera in combination with the PS-23 in order  
to get the sharpest possible image.  
• We suggest that you find an open space to work in. Focus the PS-23 so that the scene is at its  
sharpest. For best results you should disable the auto focus (if any) on either the 35mm camera  
or the video camera and manually focus the 35mm camera or the video camera. Once the image  
is sharp, then simply adjust the PS-23’s front lens to change focus.  
*An important part to remember is that you are not taking a picture of an object that is far away from  
you, but you are actually taking a picture of a phosphorous screen of the PS-23 that is only 2-3 inches  
away.  
waRnIngS anD cautIonS  
• Always remember to turn off the scope when it is not in use. If you do not plan on using your scope  
for a period of more than 10 days, you should remove the batteries.  
• Keep lens cap on when not in use.  
• Avoid contact with dust, steam, and gas.  
• The scope are not harmful to the user or the environment.  
• Do not disassemble: it will void your warranty.  
• Evaluate the scopes function by looking through it in a lit environment with the lens cap put on.  
Never use in daylight without the daylight filter lens cap on. Do not surpass ten minutes of test-  
ing.  
• Never point the scope at a bright light source.  
• Adverse atmospheric conditions such as fog, smog, or haze and a lack of ambient light (moon or  
starlight) may diminish the effective viewing distance. All technical data for this unit was compiled  
in a controlled environment.  
• If you use the rubber eyecaps for a long period of time, you may suffer skin inflammation. If you  
develop any symptoms, consult a doctor immediately.  
tRoublEShootIng  
Q: Flashes, flickers, or clicking occur while operating  
S: If it occurs within the first five minutes of inserting new batteries, it is normal and the device will  
resume normal operation soon thereafter. If it occurs for more than 10 minutes, contact for service  
instructions.  
Q: Dark spots on screen.  
S: These are either cosmetic blemishes in the intensifier tube or dust particles.  
Q: Screen becomes darker than at previous use.  
S: Replace batteries. If problem persists, contact your dealer or other authorized service repre-  
sentative for service instructions.  
Q: Image not clear.  
S: Adjust objective lens, and/or the eyepiece.  
5
ATN LIMITED LIFETIME WArrANTy  
ATN Limited Lifetime Warranty is limited to the product being free of manufacturer defects in materi-  
als and workmanship. In regards to night vision products the image intensifier tube is warranted to  
be free from manufacturer defects for a period of 2 years (defects do not include minor black spots  
or blemishes in viewing area). ATN will repair or replace said products or part thereof which upon  
inspection by ATN are found to be defective in materials or workmanship. As a condition to the ob-  
ligation of ATN to repair or replace said product, the product must be returned to ATN together with  
proof-of-purchase satisfactory to ATN. This warranty does not cover damages caused by misuse  
or improper handling. This warranty is null and void if modification or maintenance is provided by  
parties other than ATN Corp. In the event a defect that is covered by the foregoing warranty occurs  
during the applicable period stated above, ATN, at its option, will either repair or replace the product,  
and such action on the part of ATN shall be the full extent of ATN’s liability, and the Customer’s sole  
and exclusive remedy. This warranty does not cover a product (a) used in other than its normal and  
customary manner; (b) subjected to misuse; (c) subjected to alterations, modifications or repairs by  
the Customer of by any party other than ATN without prior written consent of ATN; (d) special order  
or “close-out” merchandise or merchandise sold “as-is” by either ATN or the ATN dealer; or (e) mer-  
chandise that has been discontinued by the manufacturer and either parts or replacement units are  
not available due to reasons beyond the control of ATN. ATN shall not be responsible for any defects  
or damage that in ATN’s opinion is a result from the mishandling, abuse, misuse, improper storage  
or improper operation, including use in conjunction with equipment which is electrically or mechani-  
cally incompatible with or of inferior quality to the product, as well as failure to maintain the envi-  
ronmental conditions specified by the manufacturer. cuStomER IS hEREby notIfIED that  
oPERatIon of thE EQuIPmEnt DuRIng DaylIght houRS oR unDER any EXcESSIvE  
lIght conDItIonS may PERmanEntly DamagE thE IntERnal comPonEntS of thE  
unIt anD SaID DamagE wIll not bE covERED unDER thIS waRRanty. This warranty  
is extended only to the original purchaser. Any breach of this warranty shall be waived unless the  
customer notifies ATN at the address noted below within the applicable warranty period.  
The customer understands and agrees that except for the foregoing warranty, no other warranties  
written or oral, statutory, expressed or implied, including any implied warranty of merchantability or  
fitness for a particular purpose, shall apply to the product. All such implied warranties are hereby  
and expressly disclaimed.  
2
1
LIMITATIoN oF LIAbILITy  
ATN will not be liable for any claims, actions, suits, proceedings, costs, expenses, damages or  
liabilities arising out of the use of this product. Operation and use of the product are the sole re-  
sponsibility of the Customer. ATN’s sole undertaking is limited to providing the products and  
services outlined herein in accordance with the terms and conditions of this Agreement. The  
provision of products sold and services performed by ATN to the Customer shall not be in-  
terpreted, construed or regarded, either expressly or implied, as being for the benefit of or cre-  
ating any obligation toward any third party of legal entity outside ATN and the Customer; ATN’s  
obligations under this Agreement extend solely to the Customer. atn’s liability hereunder for  
damages, regardless of the form or action, shall not exceed the fees or other charges  
paid to atn by the customer or customer’s dealer. atn shall not, in any event, be liable  
for special, indirect, incidental or consequential damages, including, but not limited to,  
lost income, lost revenue or lost profit, whether such damages were foreseeable or not  
at the time of purchase, and whether or not such damages arise out of a breach of war-  
ranty, a breach of agreement, negligence, strict liability or any other theory of liability.  
ProDucT WArrANTy rEgIsTrATIoN  
In order to validate the warranty on your product, ATN must receive a completed Product Warranty  
Registration Card for each unit. Please complete the form below and immediately mail it to our  
Service Center: ATN Corporation, 20 South Linden Ave., Suite 1B, South San Francisco CA 94080.  
Products qualifying for warranty repair will be either repaired or replaced within 10 business days of  
receipt of merchandise unless the customer is notified otherwise.  
obTAININg WArrANTy sErvIcE  
To obtain warranty service on your unit, take or send the product, postage paid, with a copy of your  
sales receipt to our service center, ATN Corporation at the address noted above. All merchandise  
must be fully insured with the correct postage; ATN will not be responsible for improper postage or,  
missing or damaged merchandise during shipment.  
6
For customer service and technical support, please contact  
American Technologies Network Corp.  
north american office  
20 South Linden Ave., Suite 1B, South San Francisco, CA 94080  
Toll Free Phone: 800-910-2862  
Phone: 650-875-0130; fax: 650-875-0129  
European office  
phone: 44(0)870-0111286, fax: 44(0) 845-3349142  
The following countries can use our  
toll free number 00 800 9102-8620  
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland  
©2006 ATN Corporation  

Avanti EWC12 EWC120B User Manual
Blaupunkt Missouri DJ70 User Manual
Canon ELURA 50 User Manual
Crown Boiler BSI276 User Manual
Dual Car Stereo System MXD105 User Manual
Epson Photo Viewer P 2000 User Manual
Hitachi DZ GX3300A User Manual
IDEAL INDUSTRIES F180 User Manual
JBL Car Amplifier A3000GTI User Manual
JVC FSUN3117 312 KD SX878R User Manual