Cabletron Systems Network Card SWPIM BRI User Manual

SWPIM-BRI  
Installation Guide  
LNK  
STS  
SWPIM-BRI  
9033038-02  
 
Only qualified personnel should perform installation  
procedures.  
NOTICE  
Cabletron Systems reserves the right to make changes in specifications and other information  
contained in this document without prior notice. The reader should in all cases consult Cabletron  
Systems to determine whether any such changes have been made.  
The hardware, firmware, or software described in this manual is subject to change without notice.  
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,  
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT  
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR  
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN  
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH  
DAMAGES.  
Cabletron Systems, Inc.  
35 Industrial Way  
Rochester, NH 03867  
2000 Cabletron Systems, Inc.  
All Rights Reserved  
Printed in the United States of America  
Order Number: 9033038-02 April 2000  
Cabletron Systems, SPECTRUM, and LANVIEW are registered trademarks and SmartSwitch is a  
trademark of Cabletron Systems, Inc.  
All other product names mentioned in this manual may be trademarks or registered trademarks of  
their respective companies.  
FCC NOTICE  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial environment.  
This equipment uses, generates, and can radiate radio frequency energy and if not installed in  
accordance with the operator’s manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause interference in which case the user  
will be required to correct the interference at his own expense.  
WARNING: Changes or modifications made to this device which are not expressly approved by the  
party responsible for compliance could void the user’s authority to operate the equipment.  
SWPIM-BRI Installation Guide  
i
 
Notice  
INDUSTRY CANADA NOTICE  
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital  
apparatus set out in the Radio Interference Regulations of the Canadian Department of  
Communications.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables  
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique  
édicté par le ministère des Communications du Canada.  
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the  
equipment meets telecommunications network protective, operational and safety requirements as  
prescribed in the appropriate Terminal Equipment Technical Requirements documents (s). The  
department does not guarantee the equipment will operate to the user’s satisfaction.  
Before installing this equipment, users should ensure that it is permissible to be connected to the  
facilities of the local telecommunications company. The equipment must also be installed using an  
acceptable method of connection. The customer should be aware that compliance with the above  
conditions may not prevent degradation of service in some situations.  
Repairs to certified equipment should be coordinated by a representative designated by the supplier.  
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give  
the telecommunications company cause to request the user to disconnect the equipment.  
Users should ensure for their own protection that the electrical ground connections of the power  
utility, telephone lines and internal metallic water pipe system, if present, are connected together. This  
precaution may be particularly important in rural areas. Caution: Users should not attempt to make  
such connections themselves, but should contact the appropriate electric inspection authority, or  
electrician, as appropriate.  
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an  
indication of the maximum number of terminals allowed to be connected to a telephone interface. The  
termination on an interface may consist of any combination of devices subject only to the requirement  
that the sum of the ringer equivalence Numbers of all the devices does not exceed 5.  
AUSTRALIAN TELECOM  
This equipment has been tested and is compliant  
with ACA TS 031.  
N826  
VCCI NOTICE  
This is a Class A product based on the standard of the Voluntary Control Council for Interference by  
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,  
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective  
actions.  
ii  
SWPIM-BRI Installation Guide  
 
Notice  
CABLETRON SYSTEMS, INC.  
PROGRAM LICENSE AGREEMENT  
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING  
GEOGRAPHICAL REGIONS:  
CANADA  
MEXICO  
CENTRAL AMERICA  
SOUTH AMERICA  
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,  
CAREFULLY READ THIS LICENSE AGREEMENT.  
This document is an agreement (“Agreement”) between You, the end user, and Cabletron  
Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron  
software program (“Program”) in the package. The Program may be contained in firmware, chips or  
other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME  
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND  
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT  
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO  
CABLETRON ORYOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE  
OF RECEIPT FOR A FULL REFUND.  
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON  
SYSTEMS +1-603-332-9400. Attn: Legal Department.  
1.  
LICENSE. You have the right to use only the one (1) copy of the Program provided in this  
package subject to the terms and conditions of this License Agreement.  
You may not copy, reproduce or transmit any part of the Program except as permitted by the  
Copyright Act of the United States or as authorized in writing by Cabletron.  
2.  
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the  
Program.  
3.  
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the  
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and  
venue of the New Hampshire courts.  
4.  
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to  
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which  
prohibit export or diversion of certain technical products to certain countries, unless a license to export  
the product is obtained from the U.S. Government or an exception from obtaining such license may be  
relied upon by the exporting party.  
If the Program is exported from the United States pursuant to the License Exception CIV under  
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program  
and agree that You will use the Program for civil end uses only and not for military purposes.  
SWPIM-BRI Installation Guide  
iii  
 
Notice  
If the Program is exported from the United States pursuant to the License Exception TSR under  
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in  
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source  
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,  
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,  
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,  
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other  
countries as may be designated by the United States Government), (ii) export to Country Groups D:1  
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign  
produced direct product is subject to national security controls as identified on the U.S. Commerce  
Control List, or (iii) if the direct product of the technology is a complete plant o r any major  
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major  
component thereof, if such foreign produced direct product is subject to national security controls as  
identified on the U.S. Commerce Control List or is subject to State Department controls under the  
U.S. Munitions List.  
5.  
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)  
was developed solely at private expense; (ii) contains “restricted computer software” submitted with  
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer  
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data  
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered  
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and  
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.  
6.  
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in  
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its  
documentation and media).  
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO  
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING  
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.  
7.  
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL  
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER  
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,  
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,  
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE  
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS  
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO  
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR  
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED  
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY  
NOT APPLY TO YOU.  
iv  
SWPIM-BRI Installation Guide  
 
Notice  
CABLETRON SYSTEMS SALES AND SERVICE, INC.  
PROGRAM LICENSE AGREEMENT  
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED  
STATES OF AMERICA AND BY UNITED STATES OF AMERICA  
GOVERNMENT END USERS.  
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,  
CAREFULLY READ THIS LICENSE AGREEMENT.  
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems  
Sales and Service, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the  
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,  
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO  
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE  
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF  
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED  
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS  
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.  
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON  
SYSTEMS +1-603-332-9400. Attn: Legal Department.  
1.  
LICENSE. You have the right to use only the one (1) copy of the Program provided in this  
package subject to the terms and conditions of this License Agreement.  
You may not copy, reproduce or transmit any part of the Program except as permitted by the  
Copyright Act of the United States or as authorized in writing by Cabletron.  
2.  
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the  
Program.  
3.  
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the  
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and  
venue of the New Hampshire courts.  
4.  
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to  
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which  
prohibit export or diversion of certain technical products to certain countries, unless a license to export  
the product is obtained from the U.S. Government or an exception from obtaining such license may be  
relied upon by the exporting party.  
If the Program is exported from the United States pursuant to the License Exception CIV under  
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program  
and agree that You will use the Program for civil end uses only and not for military purposes.  
SWPIM-BRI Installation Guide  
v
 
Notice  
If the Program is exported from the United States pursuant to the License Exception TSR under  
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in  
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source  
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,  
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,  
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,  
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other  
countries as may be designated by the United States Government), (ii) export to Country Groups D:1  
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign  
produced direct product is subject to national security controls as identified on the U.S. Commerce  
Control List, or (iii) if the direct product of the technology is a complete plant o r any major  
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major  
component thereof, if such foreign produced direct product is subject to national security controls as  
identified on the U.S. Commerce Control List or is subject to State Department controls under the  
U.S. Munitions List.  
5.  
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)  
was developed solely at private expense; (ii) contains “restricted computer software” submitted with  
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer  
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data  
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered  
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and  
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.  
6.  
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in  
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its  
documentation and media).  
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO  
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING  
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.  
7.  
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL  
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER  
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,  
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,  
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE  
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS  
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO  
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR  
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED  
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY  
NOT APPLY TO YOU.  
vi  
SWPIM-BRI Installation Guide  
 
Notice  
CABLETRON SYSTEMS LIMITED  
PROGRAM LICENSE AGREEMENT  
IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE  
FOLLOWING GEOGRAPHICAL REGIONS:  
EUROPE  
MIDDLE EAST  
AFRICA  
ASIA  
AUSTRALIA  
PACIFIC RIM  
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,  
CAREFULLY READ THIS LICENSE AGREEMENT.  
This document is an agreement (“Agreement”) between You, the end user, and Cabletron  
Systems Limited (“Cabletron”) that sets forth your rights and obligations with respect to the  
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,  
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO  
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE  
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF  
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED  
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS  
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.  
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON  
SYSTEMS +1-603-332-9400. Attn: Legal Department.  
1.  
LICENSE. You have the right to use only the one (1) copy of the Program provided in this  
package subject to the terms and conditions of this License Agreement.  
You may not copy, reproduce or transmit any part of the Program except as permitted by the  
Copyright Act of the United States or as authorized in writing by Cabletron.  
2.  
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the  
Program.  
3.  
APPLICABLE LAW. This License Agreement shall be governed in accordance with English  
law. The English courts shall have exclusive jurisdiction in the event of any disputes.  
4.  
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to  
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which  
prohibit export or diversion of certain technical products to certain countries, unless a license to export  
the product is obtained from the U.S. Government or an exception from obtaining such license may be  
relied upon by the exporting party.  
If the Program is exported from the United States pursuant to the License Exception CIV under  
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program  
and agree that You will use the Program for civil end uses only and not for military purposes.  
SWPIM-BRI Installation Guide  
vii  
 
Notice  
If the Program is exported from the United States pursuant to the License Exception TSR under  
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in  
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source  
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,  
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,  
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,  
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other  
countries as may be designated by the United States Government), (ii) export to Country Groups D:1  
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign  
produced direct product is subject to national security controls as identified on the U.S. Commerce  
Control List, or (iii) if the direct product of the technology is a complete plant o r any major  
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major  
component thereof, if such foreign produced direct product is subject to national security controls as  
identified on the U.S. Commerce Control List or is subject to State Department controls under the  
U.S. Munitions List.  
5.  
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)  
was developed solely at private expense; (ii) contains “restricted computer software” submitted with  
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer  
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data  
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered  
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and  
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.  
6.  
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in  
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its  
documentation and media).  
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO  
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING  
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.  
7.  
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL  
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER  
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,  
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,  
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE  
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS  
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO  
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR  
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED  
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY  
NOT APPLY TO YOU.  
viii  
SWPIM-BRI Installation Guide  
 
Notice  
DECLARATION OF CONFORMITY  
Application of Council Directive(s): 89/336/EEC  
73/23/EEC  
Manufacturer’s Name: Cabletron Systems, Inc.  
Manufacturer’s Address: 35 Industrial Way  
PO Box 5005  
Rochester, NH 03867  
European Representative Name: Mr. Jim Sims  
European Representative Address: Cabletron Systems Limited  
Nexus House, Newbury Business Park  
London Road, Newbury  
Berkshire RG14 2PZ, England  
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC  
EC Directive 73/23/EEC  
EN 55022  
EN 55024  
EN 60950  
EN 60825  
Equipment Type/Environment: Networking Equipment, for use in a  
Commercial or Light Industrial  
Environment.  
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged  
with this notice conforms to the above directives.  
Manufacturer  
Legal Representative in Europe  
Mr. Thomas R. Whissel  
Mr. Jim Sims  
___________________________________  
___________________________________  
Full Name  
Full Name  
Compliance Engineering Manager  
President - E.M.E.A.  
___________________________________  
___________________________________  
Title  
Title  
Rochester, NH, USA  
Newbury, Berkshire, England  
___________________________________  
___________________________________  
Location  
Location  
SWPIM-BRI Installation Guide  
ix  
 
Notice  
x
SWPIM-BRI Installation Guide  
 
INTRODUCTION  
CHAPTER 1  
APPENDIX A  
SPECIFICATIONS  
A.2 Network Interface ........................................................................A-2  
A.2.1 Pinout for the S/T-Interface Connector ...........................A-2  
A.2.2 Pinout for the U-Interface Connector ..............................A-3  
A.3 Environmental Requirements ......................................................A-3  
A.4 Regulatory Compliance ...............................................................A-4  
APPENDIX B  
FCC PART 68 - USER’S INFORMATION  
SWPIM-BRI Installation Guide  
xi  
 
Contents  
xii  
SWPIM-BRI Installation Guide  
 
INTRODUCTION  
Only qualified personnel should perform installation  
procedures.  
Welcome to the Cabletron Systems SWPIM-BRI Installation Guide. This  
manual gives an introduction to the SWPIM-BRI, lists features and  
capabilities, details the cabling pinouts, and explains how to install the  
SWPIM-BRI.  
The SWPIM-BRI provides S/T-interface (digital) functionality or  
U-interface (analog) functionality for a host platform designed to receive  
the SWPIM (Sliding WAN Physical Interface Module) architecture.  
USING THIS GUIDE  
Read through this guide completely to understand the features and  
capabilities of the SWPIM-BRI.  
A general working knowledge of WAN and Ethernet and IEEE 802.3 data  
communications networks and their physical layer components is helpful  
before using the SWPIM-BRI.  
The term “host platform” will be used to indicate the device or  
module, such as the SSR-600 or the HSIM-SSR-600, into  
NOTE  
which the SWPIM-BRI is installed.  
SWPIM-BRI Installation Guide  
xiii  
 
   
Introduction  
STRUCTURE OF THIS GUIDE  
This guide is organized as follows:  
This Introduction provides preliminary information that will aid in using  
set up and manage the SWPIM-BRI, gives an overview of the  
SWPIM-BRI and its features, and information on how to get help from  
Cabletron Systems.  
Chapter 1, Installation, provides instructions on how to install the device  
into a host platform, and gives the LED indications.  
Appendix A, Specifications, contains information on functionality and  
operating specifications, connector pinouts for the SWPIM-BRI,  
environmental requirements, and physical properties.  
Appendix B, FCC Part 68 - User’s Information, explains the FCC rules  
for the SWPIM-BRI.  
SWPIM-BRI FEATURES  
The SWPIM-BRI is installed into any Cabletron Systems product that  
supports the SWPIM architecture, such as the SSR-600, or the  
HSIM-SSR-600.  
The SWPIM-BRI uses a single RJ48 connector supporting the  
S/T-interface and the U-interface. There are two different pin assignments  
and cables for the two interfaces. Refer to Appendix A for the Cabletron  
Systems part numbers and pin assignments for these cables.  
The S/T-interface is provided via a four-wire Integrated Services Digital  
Network (ISDN) Basic Rate Interface (BRI), while the U-interface is  
provided via a two-wire ISDN BRI.  
The SWPIM-BRI provides support for the transportation of two 64 Kbps  
Bearer (B) channels and one 16 Kbps Data (D) channel for a total of  
144 Kbps. The SWPIM-BRI can be configured by software to select the  
S/T-interface for terminal equipment (TE) mode or the U-interface for  
network termination (NT) mode. Refer to the host platform software  
user’s manual for information on how to configure the SWPIM-BRI using  
software.  
The SWPIM-BRI has two LEDs, to indicate link and status conditions.  
Refer to Chapter 1 for more details.  
xiv  
SWPIM-BRI Installation Guide  
 
   
Introduction  
RELATED MANUALS  
The following Cabletron Systems manuals may help the user to set up and  
manage the SWPIM-BRI:  
SSR-600 Installation Guide  
HSIM-SSR-600 Installation Guide  
6C105 SmartSwitch 6000 Overview and Setup Guide  
Ethernet Technology Guide  
Cabling Guide  
The manuals referenced above can be obtained on the World Wide Web in  
Adobe Acrobat Portable Document Format (PDF) at the following site:  
Cabletron Systems applicable software manuals for the SSR-600 and the  
HSIM-SSR-600 host platforms (Cabletron Routing Software Manuals):  
Bridging Configuration Guide  
Event Logging System Message Guide  
Network Interface Operations Guide  
Routing Protocols Reference Guide  
Routing Protocols User's Guide  
System Software Guide  
ClearVISN Routing Configurator User's Guide  
Systems Network Architecture Guide  
Quick Reference Guide  
DTF (Data Trace Facility) User Guide  
SWPIM-BRI Installation Guide  
xv  
 
 
Introduction  
DOCUMENT CONVENTIONS  
The following conventions may be used in this document:  
Note symbol. Calls the reader’s attention to any item of  
information that may be of special importance.  
NOTE  
Tip symbol. Conveys helpful hints concerning procedures or  
actions.  
TIP  
Caution symbol. Contains information essential to avoid  
damage to the equipment.  
!
CAUTION  
Electrical Hazard Warning symbol. Warns against an action  
that could result in personal injury or death due to an electrical  
hazard.  
xvi  
SWPIM-BRI Installation Guide  
 
 
Introduction  
GETTING HELP  
For additional support related to this device or document, contact  
Cabletron Systems using one of the following methods:  
World Wide Web  
Phone  
(603) 332-9400  
Internet mail  
FTP  
anonymous  
Login  
Password  
your email address  
To send comments or suggestions concerning this document, contact the  
Cabletron Systems Technical Writing Department via the following  
email address: [email protected]  
Make sure to include the document Part Number in the email message.  
Before calling Cabletron Systems, have the following information  
ready:  
Your Cabletron Systems service contract number  
A description of the failure  
A description of any action(s) already taken to resolve the problem  
(e.g., changing mode switches, rebooting the unit, etc.)  
The serial and revision numbers of all involved Cabletron Systems  
products in the network  
A description of your network environment (layout, cable type, etc.)  
Network load and frame size at the time of trouble (if known)  
The device history (i.e., have you returned the device before, is this a  
recurring problem, etc.)  
Any previous Return Material Authorization (RMA) numbers  
SWPIM-BRI Installation Guide  
xvii  
 
   
Introduction  
xviii  
SWPIM-BRI Installation Guide  
 
CHAPTER 1  
INSTALLATION  
Only qualified personnel should install the SWPIM-BRI.  
This chapter covers the following items:  
Unpacking the SWPIM-BRI (Section 1.1)  
Installing the SWPIM-BRI into the host platform (Section 1.2)  
A description of the LANVIEW LED indications (Section 1.3)  
Connecting the SWPIM-BRI to the network (Section 1.4)  
What to do once the SWPIM-BRI is installed (Section 1.5)  
1.1  
UNPACKING THE SWPIM-BRI  
Use static electricity precautions when handling the SWPIM-BRI.  
Failure to observe static safety precautions could cause  
damage to the SWPIM-BRI. Follow static safety handling rules  
and wear the antistatic wrist strap shipped with the  
SWPIM-BRI.  
!
CAUTION  
1. Open the packing box and remove the SWPIM-BRI.  
Do not cut the non-conductive bag to remove the device.  
Damage could result from sharp objects contacting the device  
or components.  
!
CAUTION  
2. Attach the antistatic strap (refer to the instructions in the wrist strap  
package) before removing the SWPIM-BRI from the antistatic  
packaging.  
3. Verify that the SWPIM-BRI is undamaged. Refer to Getting Help if  
there is any damage to the device. Do not attempt to install the  
SWPIM-BRI if it is damaged.  
SWPIM-BRI Installation Guide  
1-1  
 
           
Chapter 1: Installation  
1.2  
INSTALLING THE SWPIM-BRI  
The SWPIM-BRI can be installed in any available open slot in the host  
platform. To install the SWPIM-BRI, proceed as follows:  
1. You do not need to power down the host platform to install the  
SWPIM-BRI. Check the host platform software manual to see if  
desired parameters would be lost from memory upon power down of  
the host platform.  
2. Remove the blank panel covering the slot in the host platform in which  
the SWPIM-BRI will be installed, by prying it off the faceplate.  
3. Ensure that the antistatic wrist strap is attached and employed as  
recommended.  
Observe all precautions to prevent damage from Electrostatic  
Discharge (ESD).  
!
CAUTION  
4. Remove the SWPIM-BRI from the antistatic bag. (Save this bag in the  
5. Hold the SWPIM-BRI with the faceplate facing away (right side up)  
from the host platform. The 40-pin connector should be facing towards  
the empty slot, with the wide part of the connector oriented down. See  
Figure 1-1.  
6. Locate the rail guides inside the slot in which the SWPIM-BRI will be  
installed, as shown in Figure 1-1.  
7. Install the SWPIM-BRI in the host platform by aligning the  
SWPIM-BRI with the rail guides in the host platform and sliding it in.  
Take care that the SWPIM-BRI slides in straight and properly engages  
the backplane host connector. Do not force the device.  
1-2  
SWPIM-BRI Installation Guide  
 
   
Installing the SWPIM-BRI  
Rail Guides  
Host Platform  
View of Host Connector End  
SWPIM-BRI  
Network Connector End  
Thumbscrew  
LNK  
STS  
SWPIM-BRI  
install  
Figure 1-1 Installing the SWPIM-BRI into the Host Platform  
8. Fasten the SWPIM-BRI with the thumbscrew.  
9. Replace power to the host platform, if necessary. Check to see that the  
host platform LED indicators go to their normal configuration. If they  
do not, remove the SWPIM-BRI from the host platform and contact  
Cabletron Systems.  
Do not connect any WAN cables until the SWPIM-BRI has been  
configured in software. The phone company can shut down a  
line that has an unconfigured connection on it.  
!
CAUTION  
10. The SWPIM-BRI must be configured before the WAN connection is  
made. Once the SWPIM-BRI has been configured, the host platform  
must undergo a soft or hard restart in order for the SWPIM-BRI to be  
recognized and for traffic to pass. Refer to the appropriate software  
manual to configure the SWPIM-BRI.  
SWPIM-BRI Installation Guide  
1-3  
 
 
Chapter 1: Installation  
1.3  
LANVIEW LED INDICATIONS  
Refer to Table 1-1 for the link LED indications for the SWPIM-BRI.  
Table 1-1 Link LED  
Color  
Indication  
Off  
Disabled or Not Configured  
Red  
Blinking Red  
Blinking Amber  
Green  
Failure  
Transmit or Receive Traffic  
Port is Active  
Refer to Table 1-2 for the status LED indications for the SWPIM-BRI.  
Table 1-2 Status LED  
Color  
Indication  
Off  
Normal or Disabled  
Blinking Amber  
Green  
Port in Loopback Test Mode  
Active Call (B1 and/or B2 is Active)  
Failure due to Framing Errors  
Blinking Green  
1-4  
SWPIM-BRI Installation Guide  
 
       
Connecting to the Network  
1.4  
CONNECTING TO THE NETWORK  
Figure 1-2 depicts a typical configuration for the SWPIM-BRI. The  
Cabletron Systems part number for the cable is 9360005-x, where x is the  
length of the cable.  
WAN Cloud  
U-interface  
Site 1  
NT  
SSR-600  
SWPIM-BRI  
U-interface  
Site 2  
SSR-600  
SWPIM-BRI  
S/T-interface  
Figure 1-2 Typical Configurations  
1.5  
COMPLETING THE INSTALLATION  
After installing the SWPIM-BRI, the SWPIM-BRI will need to be  
configured for the network. Refer to the host platform software  
documentation in order to set up and manage the SWPIM-BRI using the  
software.  
SWPIM-BRI Installation Guide  
1-5  
 
         
Chapter 1: Installation  
1-6  
SWPIM-BRI Installation Guide  
 
APPENDIX A  
SPECIFICATIONS  
This section describes the environmental specifications and safety and  
approval requirements for the SWPIM-BRI. Cabletron Systems reserves  
the right to change these specifications at any time without notice.  
A.1 PHYSICAL PROPERTIES  
Dimensions:  
1.91 H x 5.40 W x 19.05 D (cm)  
0.75 H x 2.125 W x 7.50 D (in)  
Weight (Unit):  
90.7 g (3.2 oz)  
Nominal current draw on +5V U-interface: 126.5 mA passing traffic  
supply from host platform:  
S/T-interface: 135 mA passing traffic  
MTBF (Predicted):  
3,874,392 hours  
SWPIM-BRI Installation Guide  
A-1  
 
         
Appendix A: Specifications  
A.2 NETWORK INTERFACE  
The SWPIM-BRI uses an RJ48 connector for the network port, with two  
separate pinouts, one for the S/T-interface and the other for the  
U-interface. The Cabletron Systems Part Number for the cable for both  
the S/T-interface and the U-interface is 9360005-x, where x is the length  
of the cable.  
A.2.1 Pinout for the S/T-Interface Connector  
Table A-1 Pinouts for the S/T-Interface Connection  
Function  
Pin  
Polarity  
Network  
Equipment (NE)  
Terminal Equipment (TE)  
1
2
3
4
5
6
7
8
No Connection  
No Connection  
Transmit  
No Connection  
No Connection  
Receive  
+
+
-
Receive  
Transmit  
Receive  
Transmit  
Transmit  
Receive  
-
No Connection  
No Connection  
No Connection  
No Connection  
The connector for the S/T-interface can be seen in Figure A-1:  
1 2 3 4 5 6 7 8  
strj45  
Figure A-1 S/T-Interface RJ48 Pinout  
A-2  
SWPIM-BRI Installation Guide  
 
     
Environmental Requirements  
A.2.2 Pinout for the U-Interface Connector  
The network interface pin assignments for the U-interface network  
connector are listed in Table A-2.  
Table A-2 Pinouts for the U-Interface Connection  
Pin  
Signal  
Direction  
1
2
3
4
5
6
No Connection  
No Connection  
Uline  
I/O  
I/O  
Uline  
No Connection  
No Connection  
The connector for the U-interface is shown in Figure A-2:  
1 2 3 4 5 6  
urj45  
Figure A-2 U-Interface RJ48 Pinout  
A.3 ENVIRONMENTAL REQUIREMENTS  
Operating Temperature:  
Non-operating Temperature:  
Operating Humidity:  
+5° to +40°C (41° to 104°F)  
-30° to +90°C (-22° to 194°F)  
5% to 90% (Non-condensing)  
SWPIM-BRI Installation Guide  
A-3  
 
       
Appendix A: Specifications  
A.4 REGULATORY COMPLIANCE  
This equipment meets the following safety and electromagnetic  
compatibility (EMC) requirements:  
Safety  
UL 1950, CSA C22.2 No. 950, 73/23/EEC,  
EN 60950, IEC 950, EN 60825  
Electromagnetic  
FCC Part 15, CSA C108.8, 89/336/EEC,  
Compatibility (EMC) EN 55022, EN 61000-3-2, EN 61000-3-3,  
EN 55024, AS/NZS 3548, VCCI V-3  
Telecommunications  
FCC CFR47 Part 68, CS-03  
A-4  
SWPIM-BRI Installation Guide  
 
 
APPENDIX B  
FCC PART 68 - USER’S INFORMATION  
The following instructions are provided to ensure compliance with the  
Federal Communications Commission (FCC) Rules, Part 68.  
1. This device must only be connected to the ISDN Basic Rate network  
behind an FCC Part 68 registered channel service unit. Direct  
connection is not allowed.  
2. Before connecting your unit, you must inform the telephone company  
of the following information:  
Port ID  
REN/SOC  
FIC  
USOC  
SWPIM-BRI  
6.0P  
N/A (XD)  
N/A (XD)  
3. If the unit appears to be malfunctioning, it should be disconnected  
from the telephone lines until you learn if your equipment or the  
telephone line is the source of the trouble. If your equipment needs  
repair, it should not be reconnected until it is repaired.  
4. If the telephone company finds that the equipment is exceeding  
tolerable parameters, the telephone company can temporarily  
disconnect service, although they will attempt to give you advance  
notice if possible.  
5. Under the FCC Rules, no customer is authorized to repair this  
equipment. This restriction applies regardless of whether the  
equipment is in or out of warranty.  
6. If the telephone company alters their equipment in a manner that will  
affect use of this device, they must give you advance warning so as to  
give you the opportunity for uninterrupted service. You will be  
advised of your right to file a complaint with the FCC.  
7. The attached affidavit must be completed by the installer.  
SWPIM-BRI Installation Guide  
B-1  
 
       
Appendix B: FCC Part 68 - User’s Information  
8. In the event of equipment malfunction, all repairs should be performed  
by our Company or an authorized agent. It is the responsibility of the  
users requiring service to report the need for service to our Company  
or to one of our authorized agents.  
Service can be obtained at Cabletron Systems Technical Support:  
Address:  
Cabletron Systems, Inc.  
35 Industrial Way  
Rochester, NH 03867-0505  
Phone:  
(603) 332-9400  
Internet mail:  
B-2  
SWPIM-BRI Installation Guide  
 
AFFIDAVIT FOR THE CONNECTION OF  
CUSTOMER EQUIPMENT TO 1.544 MBPS AND/OR  
SUBRATE DIGITAL SERVICES  
For the work to be performed in the certified territory of  
Telco’s name:  
State of:  
Country of:  
I,  
, of  
(Name of Authorized Representative)  
(Customer Name)  
,
(Customer’s Address)  
(Telephone Number)  
being duly sworn, state:  
I have responsibility for the operation and maintenance of the terminal  
equipment to be connected to _______________________Subrate digital  
services. The terminal equipment to be connected complies with Part 68  
of the Commission’s rules except for the encoded analog content and  
billing protection specifications. With respect to encoded analog content  
and billing protection:  
I attest that all operations associated with the establishment,  
maintenance and adjustment of the digital CPE with respect to  
encoded analog content and encoded billing information  
continuously complies with Part 68 of the FCC’s Rules and  
Regulations.  
The digital CPE does not transmit digital signals containing encoded  
analog or billing information which is intended to be decoded within  
the telecommunications network.  
The encoded analog and billing protection is factory set and is not  
under the control of the customer.  
SWPIM-BRI Installation Guide  
B-3  
 
Appendix B: FCC Part 68 - User’s Information  
I attest that the operator(s) maintainer(s) of the digital CPE responsible  
for the establishment, maintenance and adjustment of the encoded analog  
content and billing information has (have) been trained to perform these  
functions by successfully completing one of the following: Check  
appropriate one(s).  
a. A training course provided by the manufacturer/grantee of the  
equipment used to encode analog signals; or  
b. A training course provided by the customer or authorized  
representative, using training materials and instructions provided  
by the manufacturer/grantee of the equipment used to encode  
analog signals; or  
c. An independent training course (e.g. trade school or technical  
institution) recognized by the manufacturer/grantee of the  
equipment used to encode analog signals; or  
d. In lieu of the proceeding training requirements, the operator(s)  
maintainer(s) is (are) under the control of a supervisor trained in  
accordance with  
above.  
I agree to provide  
with proper documentation  
(Telco’s Name)  
to demonstrate compliance with the information as provided in the  
proceeding paragraph, if so requested.  
(Signature)  
(Title)  
(Date)  
Subscribed and sworn to me this  
day of  
, 19  
.
(Notary Public)  
My commission expires:  
B-4  
SWPIM-BRI Installation Guide  
 

Bogen Car Speaker VRS2 User Manual
Bosch Power Tools Saw RZ1 User Manual
Boston Acoustics Car Speaker RC420 User Manual
Braun Wheelchair Series A5 User Manual
Breville Toaster BTA820 User Manual
Canon Camcorder 1D X User Manual
Canon Digital Camera 0020C003 User Manual
Canon Film Camera AF 7 User Manual
Carrier Refrigerator 30GTN015 035 User Manual
Casio Watch QW 748 User Manual